A BEGINNER'S GUIDE TO PLUMBING FOR BATHTUB INSTALLATION

A Beginner's Guide to Plumbing for Bathtub Installation

A Beginner's Guide to Plumbing for Bathtub Installation

Blog Article

Schedule A Free Estimate

We have discovered the article involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the internet and think it made perfect sense to write about it with you over here.


Installing A Bathtub
Installing a bath tub isn't specifically brain surgery, but it does need solid plumbing, woodworking, and also sometimes, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably hard project. If the old bathtub is readily accessible, the project can move immediately; if you need to open a wall surface to get rid of the old bathtub and also position the new bathtub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will certainly need an assistant to vacate the old tub and also set in the new one. See to it you have certified on your own for the job as well as fit trying it. Instead of working with a service provider to take over a halfway-completed project, it is better to consider employing one prior to you begin. Possibilities are you might need a professional plumber to make tube connections.
This article will help you set up a new bath tub in your washroom if you have actually currently purchased a brand-new tub and also don't require to transform the setup of your previous water pipes.
Your devices and product list need to consist of the following:
  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Removing Old Taps


    If you require to change old faucets with new ones as a part of your setup, then the first thing you should do is disconnect the water supply. After doing so, switch on the faucets to drain any kind of water continuing to be in the system. The procedure of removing the existing faucets can be quite troublesome because of the limited gain access to that is commonly the case.
    Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have actually been eliminated, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from turning throughout this procedure. When the taps have been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
    Prior to going on to fit the new taps, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the new taps to fit.

    Suitable New Taps


    If the tails of the new taps are plastic, then you will certainly require a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipes.
    If you need to fit a monobloc, then you will certainly need minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
    Next off, position the faucet in the mounting opening in the bath/basin making sure that the washers remain in place in between the faucet and the sink. Protect the tap in position with the supplier offered backnut. As soon as the faucet is securely in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap ports. The former type must be attached to the faucet ends first, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.

    Mounting the Tub


    Utilizing the two wood boards under its feet, place the bathtub in the needed setting. The wood boards are useful in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four little factors.
    The next objective is to ensure that the tub is leveled all round. This can be attained by examining the spirit level as well as changing the feet on the bathtub till the level reviews level.
    To set up faucets, fit all-time low of the outermost versatile tap connector to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
    Turn on the water system and also check all joints and brand-new pipework for leaks and tighten them if needed. Fill up the bath tub and also inspect the overflow outlet and the normal outlet for leaks.
    Finally, repair the bathroom paneling as described in the maker's user's manual. Tiling as well as sealing around the tub needs to wait till the bath tub has been used at the very least when as this will certainly settle it right into its last position.

    Preparing for the Setup


    Firstly, the sustaining framework provided with the bathroom needs to be fitted (if required) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps device to prevent stress on the bathtub.
    Fit the versatile faucet adapters to the bottom of both faucets utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize every one of the provided washers.
    Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be suited its last placement.

    Tiling Around the Bath tub


    In the location where the bath fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to break a stiff seal, creating the water to penetrate the wall surface between the bath as well as the tiling, causing problems with wetness and also possible leaks to the ceiling listed below.
    You can select from a variety of coloured sealants to blend in your fixtures and also fittings. They are sold in tubes and cartridges, and can sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to allow for the motion experienced when the bathtub remains in usage. The sealant can fracture fairly very early if you do not think about this movement before sealing.
    Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently readily available on the marketplace. It is suggested to fit the ceramic tiles making use of water-resistant or water resistant sticky and also cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    I recently found that blog post on A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the search engines. I beg you take the opportunity to distribute this article if you enjoyed it. Thanks for your time. Visit again soon.


    Order Repair

    Report this page